Rubber bushing/rubber stopper/rubber shock absorber is vulcanized with various of material, such as EPDM, NR,SBR etc.
With Good resistance to seasonality, heat resistance, chlorination resistance, aging resistance.
Inside stainless steel and It has a very good damping effect.
Are widely applied in any area, such as furniture, Chassis instrument etc
|Rubber bushing, ruubber stopper, rubber shock absorber
|Black, white, red,etc
|As client’s requirement
|High elasticity, insulation, abrasion resistance, oil resistance, aging resistance, high temperature resistance, cold resistance, anti-corrosion, anti-static
|Meet your requirement
The advantage and property of rubber bushing/rubber stopper/rubber shock absorber
1.We adopt heighten new technology craft
2.The material of rubber bushing is complete fresh and tasteless
3.Not fade, anti-slip wear-resistant anti – pressure , damping, acid and alkali resistant
4. Environment friendly
The different material of rubber bushing will cause different property.
|> 20 Mpa
|-29°C – 65.5°C
1. the property of NR
It has good wear resistance, high elasticity, breaking strength and elongation, But in the air, it is easy to get age, and it is get sticky when it get in touch with heat, which is easy to expand and dissolve in mineral oil or gasoline, but it is resistant to strong acid, but not to Alkali . working temperature is -50~70ºC.
2. the property of EPDM
Weather ability, aging resistance, CZPT resistance, chemical stability are excellent, and CFCS and a variety of refrigerants. Working temperature is -50~150
3. the property of silicone
It has excellent heat resistance, cold resistance, CZPT resistance and atmospheric aging resistant.Good electrical insulation performance,The tensile strength and wear resistance are generally poor and has non- oil resistant. The working temperature is -55~250ºC
4. The property of NBR
Good oil resistance, heat resistance, abrasion resistance, solvent resistance and high – pressure oil,But it is not suitable for CZPT solvents, such as ketones, ozone, nitro-hydrocarbons, and chloroform. The working temperature is -40~120 ºC
5. the property of CR
It has good elasticity, wear resistance and atmospheric aging resistance. It is not afraid of violent distortion and flammability.Chemical stability. The working temperature is -40~100 ºC
6. The property of FKM
Excellent high temperature resistance,And have excellent chemical resistance, most oil and solvent (other than ketones and esters).cold resistance is not good.
These years, We are working on various project of customers and long term working in rubber industry. We have faith in giving your professional advice on your particular project.
At present, our market have been expanded to more than 30 countries, and still growing.
First we will get drawing or sample from our client to check their design. If there is no drawing or sample, we will ask some question about product concept and design idea.
Then according to what application environment of rubber part, we will help design drawing and what raw material is best for rubber part. OEM parts are ok for us.
We can meet your requirement of the design and use for different shapes and material,
And high/low temperature, foam/sponge or CZPT rubber profile, fire resistance and special property of any rubber profile and molding rubber part
The advantage of our company
1.We have excellent complete production line with advanced production and test equipment
Adding First-class technicians, so that we can offer you the competitive price and high quality ,fast delivery time .
2.We have a special drawing design department to design the correct drawing data meeting your requirements. Then, we will use CAD or other format drawing to carry on tracking the production of tooling, sample ,mass goods. To avoid something wrong to each process. To make sure all of dimension are correct.
3.We also has special production supervision department. The engineer staff will Supervise each process from the manufacture of tooling to the production of mass goods.
Reduce something wrong happened, finally offer you parts meeting your technology requirement.
4. All of Raw material are past quality certification,In the meantime, we will first delivery test report of rubber part when all of mass goods are finished. And make sure the quality meet your requirement, then make shipment.
Packing and shipment
- one part is packaged with 1 plastic bag, then certain quantity of mounting are put into carton box.
- Carton box insider rubber mounting is with packing list detail. Such as, item name, the type number of rubber mounting, quantity of rubber mounting, gross weight,net weight, dimension of carton box,etc
- All of carton box will be put on 1 non-fumigation pallet, then all carton boxes will be wrapped by film.
- We have our own forwarder which has Rich experience in delivery arrangement to optimize the most economic and quickest shipping way, SEA, AIR, DHL, UPS ,FEDEX, TNT , etc.
- Why choose us?
- 1.Product: we specialize in rubber molding,injection and extruded rubber profile.
And complete advanced production equipment and test equipment
2.High quality:100% of the national standard has been no product quality complaints
the materials are environmentally friendly and the technology reaches the international advanced level
3.The competitive price:we have own factory, and the price is directly from factory. In additional,perfect advanced production equipment and enough staff. So the price is the best.
4.Quantity :Small quantity is available
5.Tooling:Developing tooling according to drawing or sample, and solve all of questions
6.Package: all of package meet standard internal export package, carton outside, inside plastic bag for each part; as your requirement
7.Transport:We have our own freight forwarder which can guarantee our goods can be delivered safely and promptly by sea or air
8.Stock and delivery:Standard specification,lots of stocks, and fast delivery
10. Service:Excellent service after-sales
- Common Questions
- What is the minimum order quantity for your rubber products?
- Answer:We didn’t set the minimum order quantity,1~10pcs some client has ordered.
- If we can get sample of rubber product from you?
- Answer:Of course, you can. Feel free to contact me about it if you need it.
- Do we need to charge for customizing our own products? And if it is necessary to make tooling?
- Answer: if we have the same or similar rubber part, at the same time, you satisfy it.
Well, you don’t need to open tooling
New rubber part, you will charge tooling according to the cost of tooling.
In additional,if the cost of tooling is more than 1000 USD, we will return all of them to you in the future when purchasing order quantity reach certain quantity our company rule
- How long you will get sample of rubber part?
- Answer: Usually it is up to complexity degree of rubber part. Usually it take 7 to 10work days.
- How many your company product rubber parts?
- Answer:It is up to the size of tooling and the quantity of cavity of tooling. If rubber part is more complicate and much bigger, well maybe just make few, but if rubber part is small and simple, the quantity is more than 200,000pcs.
- Silicone part meet environment standard?
- Answer:Our silicone part are all high grade 100% pure silicone material. We can offer you certification ROHS and SGS, FDA .Many of our products are exported to European and American countries. Such as: Straw, rubber diaphragm, food mechanical rubber, etc.
1. Are you factory or trade company?
We specialize in manufacturing rubber and plastic manufacturer, founded in 2004
2. What’s the order process?
A: Inquiry—provide us all clear requirements, such as drawing with detail technical data, or original sample
B: Quotation—official quotation sheet with all detail specifications including price terms,shipment terms,etc
C: Payment terms—100% prepaid the cost of tooling before making new sample
T/T 30% in advanced, and the balance according to the copy of the B/L
D:Develop tooling—open the mould according to your requirement
E:Sample confirmation—send you the sample for confirmation with test report from us
F:Production—mass goods for order production
G:Shipping— by sea, air or courier. Detailed picture of package will show you.
3. What other terms of payment you use?
PayPal, Western Union
|Agricultural, Industrial, Medical, Vehicle, Electronic, Household
|EPDM, Nr, NBR, Silicone, PVC, FKM, Eptetc
|Molding or Injection
|The Name of Enterprise:
|FDA, SGS, Reach, RoHS, etc
Advantages of Injection Moulding
Whether you’re considering an injection molded part for your next project or need to replace an existing one, there are a few factors you should consider. These include design, surface finishes, tooling costs, and material compatibility. Understanding these factors can help you make the right decision. Read on to learn more about the advantages of injection molding and how to get started.
One of the most critical design factors for injection molded parts is the wall thickness. The wall thickness affects many key characteristics of the part, from its surface finish to its structural integrity. Proper consideration of this factor can prevent costly delays due to mold issues or mold modifications. To avoid this problem, product designers must carefully consider the functional requirements of the part to determine the minimum and nominal wall thickness. In addition, they must also consider acceptable stress levels, since parts with excessively thin walls may require excessive plastic pressure and may create air traps.
Another factor to consider when designing a part is its ejection and release capabilities. If the part is released from the mold, the tools should be able to slide the plastic out. Injection molds usually have two sides, one of which is ejectable, and another that remains in the mold. In some cases, special features are required to prevent part release, such as a ramp or a gusset. These design features can increase the design flexibility, but they can also increase the cost of the mold.
When designing injection molded parts, the engineering team first determines the key design elements. These elements will make sure the injection process goes as smoothly as possible. This includes factors like wall thickness, rib design, boss design, corner transition, and weld line, among others. The engineering team will then perform a design for manufacturability analysis and, if all is well, can start building and testing the mold.
Several factors can affect material compatibility of injection molded parts. When molding plastic parts, it is important to choose a material that is compatible with the part’s intended purpose. Many injection molding processes require that the two main plastic materials used are compatible with each other. This is the case in overmolding and two-shot injection molding.
The material you use to make an injection molded part will significantly impact the tolerance of the finished product. This is why material selection is as important as the design of the part. Many types of plastic resins can be used for injection molding. In addition, many of these resins can be modified or strengthened by adding additives, fillers, and stabilizers. This flexibility allows product teams to tailor the material to achieve desired performance characteristics.
One of the most common thermoplastics is polypropylene. It is extremely durable and has good impact strength and moisture resistance. This material is also recyclable and does not react with food.
One of the largest costs for manufacturing injection molded parts is tooling. For an OEM, tooling costs can range from $15K per part for a simple part to $500K for a mold with complex geometry. Tooling costs vary based on the type of steel used and the production volume of the part.
To get a reasonable estimate, companies should have a final design, preliminary design, and sample part to hand when requesting quotes. The dimensions and complexity of the cavity in a mold are crucial in determining the tooling cost, as are the part tolerances. Part tolerances are based on the area covered by the part and its functions within the mold.
The type of mold you need can also impact your tooling costs. Injection molding machines can accommodate many different kinds of molds. Some molds are made from a single mold, while others require multiple molds. Some molds can be complicated, making them unmanufacturable, which in turn drives up the cost of tooling.
The costs for tooling for injection molding are not well known, but they do add up quickly. Many product development teams tend to consider the cost of the injection molding process in terms of direct materials, machine time, and labor, but that cost model often fails to take into account additional components.
Surface finishes on injection molded parts are often used to mask defects, hide wear and tear, or enhance a product’s appearance. These finishes can also be useful when the product will come in contact with people’s hands. The surface texture you choose will depend on your desired functionality as well as the way you want to use the product. Generally, rougher textures provide better grip while masking minor molding imperfections. However, they can also make a product more difficult to release from the mold. This means that you may have to increase the draft angle of the mold. In order to get the best surface finish, the toolmaker and product designer must collaborate closely early in the design process.
There are several different surface finishes that can be used for injection molded parts. One type is known as the B-grade finish, and is compatible with a wide variety of injection molding plastics. Another type of finish is called a stone polishing process, and is ideal for parts that have no aesthetic value.
The injection moulding industry refers to overhangs on injection molded parts as “undercuts,” and these can lead to design instability. To minimize undercuts, the design must be parallel to the part’s surface. If an undercut is present, a zigzag parting line can be used.
The overhang is typically a few millimeters shorter than the surface of the mold. It is generally made from a lower-cost plastic material than the part’s surface area. The material used for the overhang should have sufficient strength to fulfill its function. An overhang will also help to prevent the piece from deforming or cracking.
Injection molding can create overhangs around the perimeter of a part. Overhangs are not always necessary; they can be added to parts as desired. Adding an overhang, however, will add substantial tooling costs. As a result, it is better to minimize the overall thickness of a design. However, in some cases an overhang can be useful to make the part look more attractive.
For parts with complex geometries, there are a few options for overhangs. Some manufacturers use side-action molds to form more complex shapes.
CNC machining of injection molded parts is a process that helps manufacturers achieve precise surfaces and shapes for their products. This process typically begins with the milling of the tooling, which is typically made of aluminum or steel. This tooling is then placed in a CNC mill. This machine carves the negative of the final plastic part, making it possible to achieve specific surface finishes. The process can be adapted to create a part with a complex structure or special features.
CNC machining allows the manufacturer to produce high-performance parts. This is possible because MIM parts do not experience induced stresses or internal pressure during the manufacturing process. Furthermore, the parts produced by MIM are more durable than CNC parts. Despite their advantages, CNC machining has its limitations, especially when it comes to design freedom and intricacy. This factor is largely dependent on the software used by the manufacturer or designer.
One drawback of CNC machining is its higher cost. Compared to injection molding, CNC machining is more expensive per part. The reason is that the initial mold cost is relatively high and is spread over a large number of parts. Once the injection molding process has been completed, the cost of the parts produced by this process becomes more competitive with those produced by machined parts. However, the cost gap increases with the volume of parts produced. This cost crossover generally occurs in quantities of at least 100 parts and can reach a maximum of 5000 parts.
The production volume of injection molded parts varies depending on the material being used. Large volumes of parts are expensive to produce, while small quantities can be produced for low cost. Injection molding requires a precise mold, which is CNC-machined from tool steel or aluminum. The mold has a negative of the part that is injected, a runner system, and internal water cooling channels to aid in cooling the part. Recent advances in 3D printing materials have made it possible to produce molds for low-volume injection molding. Previously, this was not financially viable due to the high cost of traditional mold making.
A mold is used to produce plastic parts. The molding process is very fast, with each cycle taking anywhere from 30 seconds to 90 seconds. After a part is molded, it is removed from the mold and placed on a holding container or conveyor belt. Injection molded parts are generally ready for use right away and require minimal post-processing. Injection molded parts have a similar design to a photograph, since the geometry is directly transferred to the part’s surface texture.
When selecting a plastic mold, it is important to determine the volume that the part will be produced at. If the volume is low, softer plastics may be used. However, as the part is molded over, its performance characteristics may degrade. In low-volume production, it is important to consider the overall complexity of the part. This includes the part’s draft, wall thickness, and surface finish.
editor by CX 2023-05-08